>Gallery >Shopping >Bed Slat Holders >Plastic Bed Slat Holder - 53mm for wooden frames  
 
 
 

Categories

Featured

 
 

Plastic Bed Slat Holder - 53mm for wooden frames

 

Plastic Bed Slat Holder - 53mm for wooden frames
Plastic bed slat holder 53mm for wooden frames available from Furnacc. Top fitting twin pin bed slat support for flexible slat bed bases. Pin spacings are 32mm apart (see note below). Colour brown. Buy 1 or buy 1,000. Volume prices for 30+ and 60+ slat holders.
Price:
NZ$ 4.00 excluding GST
 
NZ$ 4.60 including GST
Price for 30+:
NZ$ 3.60 per Each
Price for 60+:
NZ$ 3.00 per Each
UOM:
Each
SH55TBO
In stock
Purchase Qty:
Each
 

Open link in new tab
Open link in new tab
Open link in new tab

The S55TBO slat holder is designed for European styled wooden framed flexible slat beds and used extensively by manufacturers in New Zealand and Australia for many years.  This slat holder is top-fitting, incorporates two pins at 32mm centres, has a low profile, and is suitable for 53-54mm wide and up to 8.3mm thick laminated slats.  Critically these pins are spaced apart at 32mm centres.  Ensure that the distance between the centre of one pin and the centre of the other pin is 32mm as there are many different spacings on the market.  When assembling slats & holders leave approximately a 2mm gap inside each slat holder to allow for the flex of laminated arced slats under load.

Manufactured in Europe the S55TBO is produced to the highest standard from virgin LD-PE shock resistant thermoplastic materials to meet exact tolerances.  Each slat shoe is fully recyclable or suitable for disposal in landfill.  Available in small quantities as low as one slat holder or 100 holders.  Volume prices for 10+, 30+ & 60+ units.   Need more than 100 pieces - contact us using the 'Product Enquiry' tab.  Colour is Brown Ochre. 

Slat Holders are also known as a Posture Slat Holder; Replacement Slat Shoe; Bed Support; Slat Cap; Bed End Cap; Plastic Slat Pocket; Plastic Cap; Rubber Holder; Bed Parts; Bed Base Parts; Bed Holder; Slat Boot or Flexible Slat Shoe.

  • Simple low-profile design
  • Frequently used in slat bed manufacture
  • Brand new product from shock resistant thermoplastic materials
  • Has rigidity, toughness and resistance to stress cracking
  • Width is 59mm
  • Depth is 30mm
  • Thickness is 12mm
  • Overall cavity opening of slat holder is 54.5mm x 8.3mm
  • Pin holes are 10mm diameter and are fluted for a tighter bond
  • The distance between the centre of one pin and the centre of the other is 32mm
  • See dimensional diagram for additional information
  • Plastic is LD-PE (Low Density Polyethylene) and is fully recycleable and suitable for disposal in landfill
  • Enquire at info@furnacc.com for information on combustion properties of LD-PE
  • Replacement Bed Slat Holder - 53mm for wooden frames
    NZ$ 4.35 Each
    NZ$ 5.00 incl GST
    View / Add
  • Bed Frame Parts - 38mm Plastic Pocket
    NZ$ 4.35 Set
    NZ$ 5.00 incl GST
    View / Add
  • PIN for Slat Holder
    NZ$ 0.90 Each
    NZ$ 1.04 incl GST
    View / Add
  • Slat Bed Plastic Fitting 53mm Grey
    NZ$ 4.00 Each
    NZ$ 4.60 incl GST
    View / Add
  • Slat Holder Single Pin 53mm Ivory
    NZ$ 4.00 Each
    NZ$ 4.60 incl GST
    View / Add
  • Design Mobel Brand Slat Holder Blue
    NZ$ 5.00 Each
    NZ$ 5.75 incl GST
    View / Add
  • DM Single Slat Holder 50mm
    NZ$ 4.00 Each
    NZ$ 4.60 incl GST
    View / Add
  • Pins for Slat Holders
    View / Add
  • Slat Plastic Pocket 53mm Top Fitting
    NZ$ 5.00 Each
    NZ$ 5.75 incl GST
    View / Add
  • Continuous Slat Holder Strip 53mm
    NZ$ 32.15 Each
    NZ$ 36.97 incl GST
    View / Add

Wish to view the full range - Visit our Shopping Cart

 

Best Sellers

New

 
 
 

© Copyright 2020 Furniture Accessories Ltd